Special set with glue cartridge and special fleece

Outstanding unequal thermal expansion equalization

The bonding surfaces must be dry and free of dirt, grease and oil residues

For cleaning, we recommend Liqui Moly Cleaner and Thinner Part no

The adhesive set consists of a high-strength anaerobic adhesive with an impregnated nylon grid which is used both as a support for retention and as a catalyst for the adhesive

It has been specially developed for bonding the metal feet of rearview mirrors to windshields as well as the hinges on hinged side windows

Due to its high viscosity, it can also be used on vertical joining surfaces

LOCTITE 319

Car Rear Mirror View Adhesive Kit

Glass & Metal Glue, Antenna Aeria

Very fast repair time

Invisible, colorless joint

Shock-absorbing pad included

Flexible Doesn't damage the surface

Vibration resistant

HIGH STRENGTH - Exceptionally high strength provides a permanent repair to almost anything.

MULTIPLE MATERIALS - Some of the most common repairs are metal, glass items, ceramics and jewelry.

ENVIRONMENTAL RESISTANCE - Resists impact, moisture, heat and vibration.

Compensates different thermal expansion of parts

Fixture time: 1 min

Service temperature range: up to +120°C

Shear strength (GBMS): 10 N/mm

Product base: modified acrylic ester + activator mesh

DRIES CRYSTAL CLEAR: Ensuring a spotless finish whatever the project

GAP FILLING: Fills gaps and bonds uneven surfaces

5 MINUTE SET TIME: Gives ample time to reposition for the perfect fit

WATER RESISTANT: Withstands moderate exposure to water

EASY TO USE SYRINGE: Syringe dispenses even amounts of resin & hardener

PREPARATION: All surfaces to be bonded should be clean and dry. To improve adhesion, roughen smooth surfaces with sandpaper before gluing. Ensure your work area is well-ventilated and protected from spills. Remove stir stick from middle of plunger. With nozzle pointing upward, snap the sealing cap off the syringe then eliminate any air by slowly pushing plunger until resin and hardener reach the tip.

DISPENSE & MIX: Dispense resin and hardener onto clean, disposable surface ensuring both flow equally. Even amounts of resin and hardener can then be dispensed into a disposable mixing tray. The package blister can be used as a mixing tray. Stir the mixture for at least 20 seconds, until it is uniform. As you mix, you will notice that the epoxy warms up – this is a reaction that occurs as the resin and hardener combine.

APPLY & GRIP: Apply mixture to surface within 5 minutes. Bond strength will decrease the longer you wait to apply. Remove any excess glue immediately from project surface with a dry cloth. GRIP: To achieve maximum bond strength, clamp surfaces together and leave undisturbed for 30 minutes. Full cure achieved in 24 hours.

WHY HAS MY EPOXY NOT SET? Epoxies are made of two liquid components, a resin and a hardener. When the hardener and resin are mixed equally, the bond will be extremely strong and permanent. If the adhesive has not set it may be because the resin and hardener were not mixed in equal quantities – to ensure even distribution point tip upwards so the air bubble start to disperse and eliminate air by slowly pushing plunger until both resin and hardener are at the tip.

NOTE: Gorilla Epoxy works well on many types of plastic (roughen surfaces prior to gluing), but is not recommended for use on PVC pipe, polyethylene (PE) and polypropylene (PP) plastic, or certain types of rubber with high oil or plasticiser content. If you would like more information on how Gorilla Epoxy bonds to specific substrates, please contact our technical team via the ‘Contact Us’ section on the website for assistance.

REPOSITIONABLE: Holds in seconds but allows flexibility when positioning

100% WATERPROOF: Washer/dryer safe - ideal for fabrics

NO RUN FORMULA: For increased control

FLEXIBLE: Remains flexible once cured

CRYSTAL CLEAR: Applies and dries clear - ideal for glass

PREPARATION: All surfaces must be clean and dry

APPLICATION: Apply adhesive to each surface to be bonded. Allow adhesive to partially dry. FOR MAXIMUM BOND STRENGTH: Wait approximately 2 minutes before joining surfaces. FOR REPOSITIONAL BONDS: Wait approximately 1 minute before joining surfaces. Repositionable for 2-4 minutes depending on surface type.

NOTE: Not recommended for use on polypropylene (PP), polyethylene (PE) or polystyrene (PS) plastics or any type of rubber with high oil or plasticizer content. Also not recommended for direct or indirect food contact and should not be considered food safe.

Strong Adhesive Pads: Engineered for securely reattaching rear view mirrors and other car mirror applications, these pads provide long-lasting, reliable adhesion. Ideal for ensuring a durable, strong bond that lasts.

Multi-Functional Adhesive Strips: These versatile adhesive pads are perfect for a wide variety of applications, from car mirrors and dash cams to home improvement projects, DIY tasks, and arts & crafts. Works effectively on surfaces like wood, metal, glass, and plastic.

Discreet Black Design: The black adhesive pads blend seamlessly with your vehicle’s interior, ensuring they don’t stand out from the outside for a clean, professional appearance.

Perfect for Dash Cam Mounting: Ideal for dash cam installations, these foam pads provide a strong bond and reliable adhesion for secure placement of dash cams and rear view mirrors.

Easy to Fit and Use: Includes simple instructions for fast installation on rear view mirrors, dash cams, or any other home or DIY project. Convenient pack of 4 ensures you have enough for multiple uses.